您的当前位置：首页 DAMP auirs2184

DAMP auirs2184

来源：尔游网

Aug 29, 2011

Automotive Grade

AUIRS2184(4)S

HALF-BRIDGE DRIVER

Product Summary

Features

Floating channel designed for bootstrap operation Fully operational to + 600 V

Tolerant to negative transient voltage, dV/dt immune

• Gate drive supply range from 10 V to 20 V • Undervoltage lockout for both channels • 3.3 V and 5 V input logic compatible

• Matched propagation delay for both channels • Logic and power ground +/- 5 V offset

• Lower di/dt gate driver for better noise immunity • Output source/sink current capability (typical) 1.9 A/2.3 A

• Lead free, RoHS compliant • Automotive Qualified* • • •

Topology Half-Bridge VOFFSET 600 V VOUT

Io+ & I o- (typical) ton & toff (typical) Deadtime (typical)

10 V – 20 V 1.9 A & 2.3 A 600 ns & 230 ns 400 ns (RDT = 0 Ω) 5 µs (RDT = 200 kΩ)

Typical Applications

converter • DC/DC

• pump and compressor

• piezo injection • Starter/ alternator

Package Options 8-Lead SOIC 14-Lead SOIC AUIRS2184S Narrow Body AUIRS21844S Typical Connection

Table of Contents Description

AUIRS2184(4)(S)

Page 3 3 4 5 6 6 7 8 9-10 11 11 12 13-17 18 19-20 21 22 23

Feature Comparison Qualification Information Absolute Maximum Ratings

Recommended Operating Conditions Dynamic Electrical Characteristics Static Electrical Characteristics Functional Block Diagram

Input/Output Pin Equivalent Circuit Diagram Lead Definitions Lead Assignments

Application Information and Additional Details Parameter Temperature Trends Package Details Tape and Reel Details Part Marking Information Ordering Information Important Notice

AUIRS2184(4)(S)

Description

The AUIRS2184(4)S are high voltage, high speed power MOSFET and IGBT drivers with dependent high and low-side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, down to 3.3 V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high-side configuration which operates up to 600 V.

Feature Comparison: AUIRS2181(4)/AUIRS2183(4)/AUIRS2184(4) Part Cross- Conduction Dead-Time Ground Prevention Pins logic COM 2181 HIN/LIN no none 21814 VSS/COM 2183 Internal 500ns COM HIN/LIN yes 21834 Programmable 0.4 – 5 us VSS/COM 2184 Internal 500ns COM IN/SD yes 21844 Programmable 0.4 – 5 us VSS/COM Input Logic Ton/Toff 160/200 ns 160/200 ns 600/230 ns

†

Qualification Information

AUIRS2184(4)(S)

Qualification Level

Automotive (per AEC-Q100††)

Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level.

SOIC8

MSL3††† 260°C

(per IPC/JEDEC J-STD-020)

Moisture Sensitivity Level

SOIC14N

Machine Model

ESD

Human Body Model Charged Device Model

IC Latch-Up Test RoHS Compliant

Class M1 (Pass +/-100V) (per AEC-Q100-003) Class H1C (Pass +/-1500V)

(per AEC-Q100-002) Class C4 (Pass +/-1000V) (per AEC-Q100-011) Class II, Level A†††† (per AEC-Q100-004)

Yes

† †† †††

Qualification standards can be found at International Rectifier’s web site http://www.irf.com/Exceptions to AEC-Q100 requirements are noted in the qualification report.

Higher MSL ratings may be available for the specific package types listed here. Please contact your International Rectifier sales representative for further information.

†††† IN, SD, DT Class II Level B at 40mA per JESD78.

AUIRS2184(4)(S)

Absolute Maximum Ratings

Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM lead. Stresses beyond those listed under \"Absolute Maximum Ratings\" may cause permanent damage to the device. These are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in the “Recommended Operating Conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Ambient temperature (TA) is 25°C, unless otherwise specified. Symbol Definition Min Max Units VB VS VHO VCC VLO DT VIN High-side floating absolute voltage High-side floating supply offset voltage High-side floating output voltage Low-side and logic fixed supply voltage Low-side output voltage Programmable deadtime pin voltage -0.3 VB - 25 VS - 0.3 -0.3 -0.3 VSS -0.3 VSS -0.3 VCC - 20 — (8-lead SOIC) PD Package power dissipation @ TA ≤ 25°C (14-lead SOIC) (8-lead SOIC) RthJA TJ Thermal resistance, junction to ambient Junction temperature (14-lead SOIC)— — — — — 620 VB + 0.3 VB + 0.3 20 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 50 0.625 1.0 200 120 150 °C/W W V/ns †V Logic input voltage (IN & SD)VSS Logic ground dVS/dt Allowable offset supply voltage transient TS Storage temperature -50 150 °C TL Lead temperature (soldering, 10 seconds) — 300 † All supplies are fully tested at 25 V and an internal 20 V clamp exists for each supply.

www.irf.com

Recommended Operating Conditions

AUIRS2184(4)(S)

The input/output logic timing diagram is shown in Figure 1. For proper operation the device should be used within the recommended conditions. The VS and VSS offset rating are tested with all supplies biased at a 15 V differential.

Symbol Definition Min Max Units VB High-side floating supply absolute voltage VS + 10 VS + 20 VS High-side floating supply offset voltage (††) 600 VHO High-side floating output voltage VS VB VCC Low-side and logic fixed supply voltage 10 20 V VLO Low-side output voltage 0 VCC †††)VIN VSS VCC Logic input voltage (IN & SD)(DT Programmable deadtime pin voltage VSS VCC VSS Logic ground -5 5 TA Ambient temperature -40 125 °C †† Logic operational for VS of -5 V to +600 V. Logic state held for VS of -5 V to –VBS. (Please refer to Design Tip DT97-3 for more details).

††† HIN and LIN are internally clamped with a 5.2 V zener diode.

Dynamic Electrical Characteristics

Unless otherwise noted, these specifications apply for an operating junction temperature range of -40°C ≤ Tj ≤ 125°C with bias conditions of VBIAS (VCC, VBS) = 15 V, VSS = COM, CL = 1000 pF.

Symbol Definition MinTyp Max Units Test Conditions ton Turn-on propagation delay — 600900VS = 0 V toff Turn-off propagation delay — 230400VS = 0 V or 600 V tsd Shut-down propagation delay — 220350

MTon Delay matching, HS & LS turn-on — 3 90

MToff Delay matching , HS & LS turn-off — 15 40 t r Turn-on rise time — 15 60 VS = 0 V

t f Turn-off fall time — 12 35

RDT = 0 Ω Deadtime: LO turn-off to HO turn-on (DTLO-HO) & 280375520

HO turn-off to LO turn-on (DTHO-LO) 3.95 6 µs RDT = 200 kΩ

— 0 50 RDT = 0 Ω

MDT Deadtime matching DTLO-HO - DTHO-LO ns

— 0 600RDT = 200 kΩ

AUIRS2184(4)(S)

Static Electrical Characteristics

Unless otherwise noted, these specifications apply for an operating junction temperature range of -40°C ≤ Tj ≤ 125°C with bias conditions of VBIAS (VCC, VBS) = 15 V, VSS = COM. The VIL, VIH and IIN parameters are referenced to VSS/COM and are applicable to the respective input leads: IN andSD. The VO, IO and Ron parameters are referenced to COM and are applicable to the respective output leads: HO and LO.

Test Conditions Symbol Definition MinTyp Max Units VIH Logic “1” input voltage for HO & logic “0” for LO 2.5— — VIL Logic “0” input voltage for HO & logic “1” for LO — — 0.8VCC = 10 V to 20 V2.5— — VSD,TH+ SDinput positive going threshold V — — 0.8VSD,TH- SDinput negative going threshold VOH High level output voltage, VBIAS - VO — — 1.5IO = 0 A VOL Low level output voltage, VO — — 0.2IO = 20 mA ILK Offset supply leakage current — — 50 VB = VS = 600 V µA IQBS Quiescent VBS supply current 10 50 130VIN = 0 V or 5 V IQCC Quiescent VCC supply current 0.41.01.3mA IIN+ Logic “1” input bias current — 25 60 IN = 5 V,SD= 0 VµA IIN- Logic “0” input bias current — — 5.0IN = 0 V,SD= 5 VVCCUV+ VCC and VBS supply undervoltage positive going 8.08.99.8VBSUV+ threshold VCCUV- VCC and VBS supply undervoltage negative going V 7.48.29.0VBSUV- threshold VCCUVH Hysteresis 0.30.7— VBSUVH VO = 0V, (†)PW ≤ 10us, Output high short circuit pulsed current 1.41.9— IO25+ TJ = 25°C IO25- IO+ (IO-(†)(††) (†)Output low short circuit pulsed current Output high short circuit pulsed current Output low short circuit pulsed current 1.81.21.52.3— — — — — A VO = 15V, PW ≤ 10us, TJ = 25°C VO = 0 V, PW ≤ 10 µs VO = 15 V, PW ≤ 10 µs †)(††) (†) Guaranteed by design (††) IO+ and IO- decrease with rising temperature

www.irf.com

Functional Block Diagram: AUIRS2184, AUIRS21844 AUIRS2184(4)(S)

www.irf.com

Input/Output Pin Equivalent Circuit Diagrams: AUIRS2184S

AUIRS2184(4)(S)

www.irf.com

Input/Output Pin Equivalent Circuit Diagrams: AUIRS21844S

AUIRS2184(4)(S)

Lead Definitions

Symbol Description Logic input for high-side and low-side gate driver outputs (HO and LO), in phase with HO IN (referenced to COM for AUIRS2184 and VSS for AUIRS21844) Logic input for shutdown (referenced to COM for AUIRS2184 and VSS for AUIRS21844) SD DT Programmable deadtime lead, referenced to VSS (AUIRS21844 only) VSS Logic ground (AUIRS21844 only) VB High-side floating supply HO High-side gate drive output VS High-side floating supply return VCC Low-side and logic fixed supply LO Low-side gate drive output COM Low-side return Lead Assignments: AUIRS2184(4)S www.irf.com © 2008 International Rectifier

AUIRS2184(4)(S)

Application Information and Additional Details

Figure 1: Input/Output Timing Diagram

Figure 2: Switching Time Waveform Definitions

Figure 3: Shutdown Waveform Definitions Figure 4: Deadtime Waveform Definitions

Figure 5: Delay Matching Waveform Definitions

Parameter Trends vs. Temperature and vs. Supply Voltage

AUIRS2184(4)(S)

Figures of this chapter provide information on the experimental performance of the AUIRS2184(4)S HVIC. The line plotted in each figure is generated from actual lab data.

A large number of individual samples were tested at three temperatures (-40 ºC, 25 ºC, and 125 ºC) in order to generate the experimental curve. The line consists of three data points (one data point at each of the tested temperatures) that have been connected together to illustrate the understood trend. The individual data points on the Typ. curve were determined by calculating the averaged experimental value of the parameter (for a given temperature).

A different set of individual samples was used to generate curves of parameter trends vs. supply voltage.

Turn-on Propagation Delay (ns)Turn-on Propagation Delay (ns)700650Max.140012001000800600400101214161820Supply Voltage (V)Max.600550500Typ.Min.Typ.-50-250255075100125Temperature (oC)Figure 6A. Turn-on Propagation Delay vs. Temperature Figure 6B. Turn-on Propagation Delay vs. Supply Voltage

Turn-off Propagation Delay (ns)Turn-off Propagation Delay (ns)350300250200150Max.6005004003002001000101214161820Supply Voltage (V)Max.Typ.Typ.Min.-50-250255075100125Temperature (oC)Figure 7A. Turn-off Propagation Delay vs. Temperature Figure 7B. Turn-off Propagation Delay vs. Figure 7B. Turn-off Propagation Delay vs. Figure 7B. Turn-off Propagation Delay Supply Voltage Supply Voltage vs. Supply Voltage

www.irf.com

) AUIRS2184(4)(S)

500

350)ns ( ayl300 eD n oita250 gapoMax. rP200D Typ. SMin. 150-50-250255075100125 Temperature (oC) Figure 8A. SD Propagation Delay vs. Temperature

18- ) 16sMax.n(e 14mTyp.iT12 llafMin. 10ffO-n8ruT-50-250255075100125Temperature (oC) Figure 9A. Turn-off Fall Time vs. Temperature

20)sn( 18emiax. Te16MsiTyp.R n14O-Min.nruT1210-50-250255075100125Temperature (oC) Figure 10. Turn-on Rise Time vs. Temperature

www.irf.com

sn ( ya400l eD n300Max. oita ga200Typ.p oPr100 DS 0 101214161820 Supply Voltage (V) Figure 8B. SD Propagation Delay vs. Supply

Voltage

Figure 11. Deadtime vs RDT

450Max. 400 )sTyp.n ( em350Min. i tda eD300 250 -50-25025 5075100125Temperature ( o C) Figure 12A. Deadtime vs Temperature

2.0 ) V(1.5Max. ut putTyp. O 1.0leMin. veL h0.5giH 0.0-50-250255075100125 Temperature (oC)

Figure 13. High Level Output vs. Temperature (IO = 0 mA) )A40u( tnerr30uC egak20aMax.eL ylp10puSMin.Typ. tes0ffO-50-250255075100125 Temperature (oC)

Figure 15. Offset Supply Leakage Current vs.

Temperature

www.irf.com

AUIRS2184(4)(S)

1100 900 )sn ( e700 imMax.ud a500Typ.e D300Min. 100 101214161820 Supply Voltage (v) Figure 12B. Deadtime vs. Supply Voltage

140)V120(m put100Out Max.lev80Typ. LewoMin. L60-50-250255075100125Temperature (oC) Figure 14. Low Level Output vs. Temperature

)Au120( tner100ru Cylp80Max.puS S60BTyp.V nte40Min.cseiu20Q -50-250255075100125Temperature (oC)

Figure 16. VBS Supply Current vs. Temperature

)A1100(u trenr1050Max.Cu yl1000Typ.uppS CMin.CV950 entcsei900uQ-50-250255075100125 Temperature (oC)

Figure 17A. Vcc Supply Current vs. Temperature

40)A(u ntrer30Cu saMax.iB t20Typ.npu I\"Min. 1\" ci10 Log-50-250255075100125Temperature (oC) Figure 18. Logic “1” Input Bias Current vs. Temperature

10.0)V( dl9.5hosrehMax.T 9.0+Typ.UV BSV8.5Min. d anCC8.0V-50-250255075100125Temperature (oC) Figure 20. VCC and VBS Undervoltage Threshold (+) vs.

Temperature

www.irf.com

AUIRS2184(4)(S)

Figure 17B. VCC Supply Current vs. VCC Supply

Voltage (V)

0.00 ).A (u -0.02nterMax.ru-0.04 CsTyp.aiB-0.06Min. utpn-0.08 I\"0\" cig-0.10oL-50-250255075100125 Temperature (oC)Figure 19. Logic “0” Input Bias Current vs. Temperature )9.0 (V dlhos8.5rehMaxT -UV8.0Typ. SBMin.V nd7.5 aCCV7.0-50-250255075100125Temperature (oC)Figure 21. VCC and VBS Undervoltage Threshold (-) vs.

Temperature

Output Source Current (A)

5Output Source Current (A) AUIRS2184(4)(S) 432Typ.

1Min.0101214161820Supply Voltage (V)Figure 22. Output Source Current (A) vs. Temperature

Figure 22A. Output Source Current (A) vs. Supply

Voltage (V)

5Output Sink Current (A)432Typ.1Min.0101214161820Supply Voltage (V)Figure 23. Output Sink Current (A) vs. Temperature

Figure 23A. Output Sink Current (A) vs. Supply

Voltage (V)

www.irf.com

Package Details: SOIC8

AUIRS2184(4)(S)

Package Details: SOIC14N

www.irf.com

Tape and Reel Details: SOIC8

LOADED TAPE FEED DIRECTION

AUIRS2184(4)(S)

BAH www.irf.com DFC

NOTE : CONTROLLING DIMENSION IN MMEGCARRIER TAPE DIMENSION FOR 8SOICNMetricImperialCodeMinMaxMinMaxA7.908.100.3110.318B 3.904.100.1530.161C11.7012.300.460.484D5.455.550.2140.218E6.306.500.2480.255F5.105.300.2000.208G1.50n/a0.059n/aH1.501.600.0590.062FDCBAEGHREEL DIMENSIONS FOR 8SOICNMetricImperialCodeMinMaxMinMaxA329.60330.2512.97613.001B20.9521.450.8240.844C12.8013.200.5030.519D1.952.450.7670.096E98.00102.003.8584.015Fn/a18.40n/a0.724G14.5017.100.5700.673H12.4014.400.4880.566© 2008 International Rectifier

Tape and Reel Details: SOIC14N

LOADED TAPE FEED DIRECTION AUIRS2184(4)(S)

BAH www.irf.com DFCNOTE : CONTROLLING DIMENSION IN MMEGCARRIER TAPE DIMENSION FOR 14SOICNMetricImperialCodeMinMaxMinMaxA7.908.100.3110.318B 3.904.100.1530.161C15.7016.300.6180.1D7.407.600.2910.299E6.406.600.2520.260F9.409.600.3700.378G1.50n/a0.059n/aH1.501.600.0590.062FDCBAEGHREEL DIMENSIONS FOR 14SOICNMetricImperialCodeMinMaxMinMaxA329.60330.2512.97613.001B20.9521.450.8240.844C12.8013.200.5030.519D1.952.450.7670.096E98.00102.003.8584.015Fn/a22.40n/a0.881G18.5021.100.7280.830H16.4018.400.50.724

Part Marking Information

SOIC8:

AUIRS2184(4)(S)

SOIC14N:

AUIRS2184(4)(S)

Ordering Information

Base Part Number

Package Type

Complete Part Number

Form Quantity Tube/Bulk 55 AUIRS2184S

SOIC8

Tape and Reel

AUIRS21844S

SOIC14N

2500

AUIRS2184STR AUIRS21844S AUIRS21844STR AUIRS2184S

Standard Pack

Tube/Bulk 55 Tape and Reel

2500

www.irf.com

IMPORTANT NOTICE

AUIRS2184(4)(S)

Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment.

IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed.

IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards.

Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions.

Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements.

IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product.

IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements.

For technical support, please contact IR’s Technical Assistance Center

http://www.irf.com/technical-info/

WORLD HEADQUARTERS:

101 N. Sepulveda Blvd., El Segundo, California 90245

Tel: (310) 252-7105

www.irf.com

因篇幅问题不能全部显示，请点此查看更多更全内容

查看全文