FM-3038TM2-5ANIR Receiver Modules for Remote Control Systems
Description
The FM-3038TM2-5ANisremote control receiver modules.Pin diode and receiver IC are assembled on one module.Small-sized, light-weight, and low current consumption.modules have been achieved by using resin mold.
The demodulated output signal can directly be decoded by a microprocessor.The main benefit is the reliable function even in disturbed ambient and theprotection against uncontrolled output pulses.
Features
Supply Voltage Range: 2.7V to 6.5VTTL and CMOS compatibility
Photo detector and preamplifier in one package.Internal filter for PCM frequency
Open collector output (built-in Pull-up resistor(40K)Output active low
Enhanced Immunity against all kinds of disturbance light
No occurrence of disturbance pulses at output pin within nominal conditions.Short settling time after power On.( below 1msec)Meet RoHS
Application Circuit
47~100ΩIR Receiver ModuleVCCVCC47ufVOUTTransmitterMCUR-C filter recommended to suppress power supply disturbances.
R-C filter should be connected closely between VCCpin and GND pin.
ICGNDGNDBlock DiagramOrdering Info.(carrier frequencies)
Type
FM-3032TM2-5ANFM-3036TM2-5ANFM-3038TM2-5ANFM-3040TM2-5ANFM-3056TM2-5AN
Carrier Frequency(fo)
32.7 K36.7 K37.9 K40.0 K56.7 K
光電企業有限公司
November 2006 Rev 1.1
FM-3038TM2-5ANAbsolute Maximum Ratings
Parameter
Supply VoltageOutput VoltageOutput CurrentOperating TemperatureStorage TemperatureSoldering Temperature
SymbolVCCVOUTIOUTToprTstgTsd
Ratings7.00.2 ~Vcc2.5-20 ~ +80-30 ~ +85260℃, Max 5sec
(Ta = 25℃)
UnitV VmA ℃℃℃
Electro-optical Characteristics
ParameterSupply VoltageSupply CurrentMax input currentOutput VoltagePeak Wave Length
SymbolVccICCIINVohVol
Min.2.70.80.5Vcc-0.5
--±0˚
Arrival Distance
L
±30˚±45˚
Max. Voltage GainInternal Pull-up Resistor
BPF BandwidthBPF frequencyOutput Pulse width
AvRpulfbwfcTpw
---7036--3.5450
Typ.5.01.01.0-0.294015107703.5fo600
Max.6.51.31.5-0.4----8244-+3.5750
UnitVmAmAVVnmmmmdB㏀kHz%㎲
(Ta = 25℃)
No input signal
Vin=0Vcc=5V
λp
Fig.1,2,3fin=37.9kHzVin=30㎶pp
fin=37.9kHzVin=30㎶pp
Fig.1,2,6
光電企業有限公司
November 2006 Rev 1.1
FM-3038TM2-5AN[ Fig.1] Data Signal diagram
Data Wordt PauseenlargeCarrier Frequency : fot Burst(Output pulse)
t Gapt Gap : Signal gap time between two burst in pulses of carrier.Minimum Gap Time ≧300ust Burst : Length of a burst in pulses of the carrier frequency.Minimum Burst ≧300ust pause : Data pause between two data words.Minimum Data PauseTime ≧20ms
[ Fig.2 ] Transmitter
10KVCC
S/TransmitterPD100ufVOUT
10K30㎝GND
※The specifications shall be satisfied under the following conditions. The standard transmitter
shall be specified of the burst wave form adjusted to VOUT200mVp-p upon Po measuring circuit Standard Transmitter [ Fig.3 ] Test condition of arrival distanceVoutoscTransmitterGNDVcc: Indicates horizontal andvertical directions[ Measurement condition for arrival distance]☞Ambient light source : Detecting surface illumination shall be irradiate 200±50Lux
under ordinary white fluorescence lamp without high frequency lighting
光電企業有限公司
November 2006 Rev 1.1
FM-3038TM2-5ANElectrical/Optical Characteristics
[ Fig.4 ] Supply Current vs. Voltage
2.5[ Fig.5 ] Sensitivity vs. Supply Voltage
100Relative Sensitivity(%)806040200Supply Current(㎃)2.01.51.00.50.02.53.03.54.04.55.05.56.06.52.53.03.54.04.55.05.56.06.5Supply Voltage(V)Supply Voltage(V)[ Fig.6 ] Output Pulse Width vs. Distance
900[ Fig.7 ] Directivity (Horizontal/Vertical)0˚20˚40˚Relative Radiant(˚)Output Pulse Width(㎲)8007006005004003000481216202428806040200Relative Sensitivity(%)
1009060˚VH80˚Transmission Distance(m)[ Fig.8 ] BPF Fc Curve
BPF fc1.2ESD Test Results
Parameter1Relative responsivity0.80.60.40.200.50.60.70.80.911.11.21.3f/fo Relative Frequency1.41.5ConditionsC=200㎊R=0ΩC=100pfR=1.5KΩSpecificationMin ±200VResults>±200VMachine ModelHuman Body ModelMin ±2000V>±2000V光電企業有限公司
November 2006 Rev 1.1
FM-3038TM2-5AN光電企業有限公司
November 2006 Rev 1.1
FM-3038TM2-5AN1. Packing unit for Remote control modulePackageTransfer moldTypeDevicePackingMethodPoly BagUnits /Tube200Poly Bag/Inner BoxPartialMax Devices /Max Inner Box /Shipment ofInner BoxOuter BoxOuter Box5100010* Inner Box # 1* Inner Box # 1* Outer Box # 2* Outer Box # 3(unit : mm)Inner Box #1 with Opto-Sensor Logo (170*240*65)Outer Box #2 with Opto-Sensor Logo (365*360*270)Outer Box #3 with Opto-Sensor Logo (385*750*300)
2. Packing method
1) Input max 200 units to one Poly bag and label should be attached middle of it.
Antistatic Vinyl 2) Input 5 poly bags to one inner box and label should be attached as below.
Label #13) Input 10 inner boxes to outer box.
4) Input 2 outer boxes into Box #3.
光電企業有限公司
November 2006 Rev 1.1
